Version 2.3 (May 28th 2022)
Improved accuracy of Weight and Balance popup clickspots and cursor position.
Added pointer-hand cursor to weight and balance popup.
Added Docking Mode Toggle command: "thranda/operations/DockingModeToggle"
Added: Releasing the parking brake will toggle SlewMode / Docking Hold off.
Adjusted nose wheel steering sensitivity to improve ground handling and control.
Adjusted torque green arc limit to correspond to 1670 ft-lbs.
Adjusted prop airfoil to fix slow climb rate when at 2200 RPM.
Icing placard warning is hidden when the de-ice system is enabled.
Adjusted spacing on MISC popup page for "Anti Ice Equipped" line.
Added Synthetic Vision Plugin for the G1000.
Add manifest option "SeatClickLbs" to set how much weight gets added when clicking on a seat in the W&B popup.
Add Auto-trim system. As flaps are extended or retracted the pitch trim automatically runs to compensate for the nose-up or nose-down moments. Active above 35 knots and when flaps are extended 5 degrees or more.
Add visible cargo in the cargo pod.
Fixed COM frequency swap buttons on G1000.
Version 2.2.1 (January 27th 2021)
Tweaked airfoils so less nose-down trim is required in cruise flight
Fixed yaw damper being stuck on when using the G1000 bezel autopilot
Fixed missing menu clickspots for tiedowns when using the Amphibian
Increased idle fuel flow to be more realistic
Added green Engine Inlet Norm annunciator
STEC55 Autopilot: AUTO mode for yaw damper will turn it on and off with AP servos
Added visual feedback to "Load" and "Save" buttons on Weight and Balance pop-up
Fixed range of anti-ice intensity knob
Fixed water rudder to retract/deploy depending on where you start
Amphibian tie-downs can be independently removed
ELT sound fixed
Version 2.2 (September 17th 2020)
-Added ability to make use of PBR in dynamic livery creator.
-Oxygen system now handles the cargo variant
-Removed old Documentation
-Added new Synthetic Vision for G1000
-Adjusted nosewheel deflection rate
-Fixed flight Hobbs meter not working
-Added yaw damper
-Adjusted trim defaults and rates
-Adjustments to stall AoA, pitch attitude during landing
-Tuned cruise speeds, climb performance
-Adjusted propeller low-pitch stop setting
-Improved VR compatibility for pop-up menu
-Adjusted nominal battery voltage to 24.5 V
-Adjusted stall warning horn alpha
-Fixed log errors with FMOD sound
-Fixed AC popup temp/fan buttons getting stuck on
-Fixed G1000-related Log errors
-Possible fix for random "clunk" sound while flying (button03_cue)
-Add panning and course-sync clickspots to 2D G1000 pop-ups
-Added tail stand to wheeled Kodiak to prevent tipping backward while loading cargo/pax
-Added De-ice and Oxygen quantity and resets to weight and balance pop-up menu
-Adjusted electrical bus assignments to split loads across the two buses
-Fixed water rudder commands not working for the amphibian
Version 2.1 (January 2020)
-Added magnetic compass
-Fixes to Librain effects
-Adjusted structural icing visual effect on lower wing surfaces
-Better support for SkunkCrafts updater
-Moved several user preferences out of "manifest.json" and into separate config files
-Added relevant files to SkunkCrafts updater ignorelist
Version 2.0 (November 20th 2019)
Completely overhauled SASL to become SASL3
Added expansion pack to base pack
Added de-ice and exterior surface ice visualization
Added optional TKS de-ice equipment and switches, can be toggled via the 2D pop-up
New oxygen system and simulation
Completely overhauled sound to take more advantage of improvements in FMOD
Completely overhauled flight dynamics and water dynamics
Added custom indicated airspeed error, compared to calibrated airspeed
Added mud flap option
Added ability to select between G1000 in-bezel autopilot and S-TEC 55 autopilot.
Added synthetic vision
Made improvements to VR configuration
Improved custom annunciator system; the background scales with the number of items
Improvements to custom annunciator triggers and logic
Environmental system electrical draw is dependent on heaters and fan speed now
Rewrite of weight and balance module
Weight and balance weights can be saved and automatically loaded for the next flight
"Simplified" engine mode now has correct engine reverser behavior
Version 1.60 (Feb 2nd 2018)
Removed Carenado’s G1000 and related infrastructure (now using LR G1000 exclusively)
Added VR camera snap points
Caused prop to disappear when shaft is broken
Removed throttle limiter with realism on
Updated version splash screen on MFD
improved generator, battery, oil temp, etc.
Calibrated cruise speeds with new engine performance
Adjusted yellow line in G1000 screen
fixed low idle to 53%
Added VR-compatible click spots to the autopilot in the 3D panel
Prepared oxygen system and .acf file for X-plane 11.20 oxygen update.
Tweaked ELT threshold
Deactivated Slew mode by default
Remixed internal sounds
Tweaked weight and balance code
Changed autopilot altitude step size from 10 to 100
Updated “Localizer intercept to auto-engage BC” value to match the real G1000.
Added ground roll and shaft damage sounds.
Fixed high ITT during start
Tweaked windows to reflect aircraft interior
Added ENG INLET BP CAS annunciator
Made brakes non-hydraulic
Updated documentation folder
Version 1.5 (Dec 16th 2017)
Major update for X-Plane 11.10+
Added support for Laminar’s native G1000 (Icons and .acf name have a description of which G1000 users have selected to use).
Added ability to save various preferences set in the pop-up window (such as weight units, fairings, chocks, etc.
Updated SASL to v2.51, which now allows for SASL to not be force-reset after a crash.
Added a “Startup Running On/Off” option, which resets the plane immediately to the desired condition, provided the plane is stationary on the ground.
Re-authored all audio as FMOD. (Removed previous in-house audio plugin).
Removed all instances of degenerate UVs (known colloquially as the “Marching Ants” problem)
Calibrated turbine curves, taking advantage of XP11.10’s new PT6 modelling capabilities
Re-calibrated entire flight dynamics to match XP11.10’s new flight physics
Re-calibrated ground handling, to match XP11.10’s new ground physics
Fixed dynamic livery generator to allow for “-“ characters in aircraft registration
Fine-tuned PBR materials inside and out
Fixed landing light covers transparency and PBR
Re-authored all click spots to be X-plane native (in anticipation of VR support). Previous Thranda-based scroll wheel implementation will not be supported in VR, so it had to be revamped.
Added X-Plane-native checklist file (which Laminar says will be the basis for future G1000-integrated checklist capability)
Adapted electrical systems logic to new v11.10 electrical model
Assigned different sound events to various sliders in the “Audio/Slew” tab of the pop-up window.
Reworked all SASL-based panel elements to do a single-pass graphics draw, as opposed to multi-pass, to reduce load on GPU.
Re-optimized all exported OBJ files, to continue saving FPS
Calibrated oxygen system to allow for about 5 hours of oxygen
Updated Water Handling to conform better to XP11.10’s new water physics.
Fixed light halo artifacts.
Fixed firewall smoke handle direction